Installation Tutorial

1. Alr Bubbles: it may happen during installing, using safety pin, poke a small hole in the air bubble and gently rub out the air while re-adhering raised pad to the surface.
2. Lay the materials out upside down to expand out.
3. Put it in the sunlight for a while. it is normal that the material will shrink, and this will prevent it from shrinking after it is installed on the boat.
4. The adhesive backing adheres primarily to flat metal and fiberglass surfaces. For some uneven or textured surfaces, such as wood floors and plywood decks, it is recommended to use polyurethane glue to enhance adhesion.
5. Rolling it in a box is a safe and most cost-effective way for transportation. The rolling pressure may result inslight separation of the backing paper from the foam at both ends. Please cut off a little bit of the end section if needed. likewise, the unrolling process will inevitably result in creasing of the adhesive backing paper. As long as the glue and foam do not detach, the adhesion will not be affected.

• Scouring pad: Wash the floor cleanly, get rid of any dirt.
• Towel: Clean the surface and wipe away any residue.
• Chemical cleaners (isopropyl alcohol or acetone) : Used for final surface preparation prior to installation.
• Utility knife, scissors: Use of sharp blades, trim the template material and EVA boat decking sheet to size.
• Tape measure, pencil: To mark the area you want to cut on your sheet before start cutting it.
• Ruler: To help you draw straight lines.
• Safety pin: Used to remove air bubbles that may occur during installation
• Femplate material (optional) : it is recommended to use clear Mlylar stencil sheet for creating a pattern before cutting. It allows you to measure the area where you’d like to cover and figure out how to trim the EVA foam boat decking. Then you can easily cut the EVA boat decking sheet to fit your boat shape and reduce more offcuts.
• Marking tape (optional) : Tape down the template so it does not move.

–Remove the old carpet if it has one.

–Wash the floor cleanly, get rid of any dirt. Use organic solvent (acetone or alcohol) to clean off the surface the deck must be clean and free of grease, dust and other contaminants.

–Dry off the surface with a towel, then wipe down the floor with chemical cleaning to entire boat.

–Be sure to dry off the surfaces before sticking it down. Any moisture may weaken the adhesion.

Decide what kind of decking style you want. Take measurements and cut.

Method 1: Measure the area where you’ll be installing the decking. Draw out the sheet with measurements on the template. Or just marking on the surface of the EVA foam as long as you make your measurements and planning. Use a ruler or the template to cut the line straight down.

Method 2: Place the EVA foam boat floor piece on top of the boat and use an utility knife to cut out pieces to line up with the hatch and hinges on the floor. Cut out the hinge seams.

NOTE: The knife may damage the surface of your boat, be careful not to cut too hard or too deep.

1. Before installing, make sure that each piece has the same brush pattern and is oriented the same direction throughout the boat. If you find that the teak pattern is not aligned or does not match or that another sheet of the same color has a different shade of color, please rotate the sheet 180 degrees to make it symmetri-cal.
2. With the EVA deck pad in place, peel the backing down appx. 2″ across the entire piece and crease the paper(this helps hold the exposed adhesive above the surface when ensuring piece is still properly aligned).
3. Lightly tack the exposed adhesive down. Do not reposition the adhesive once you have stuck it on. Avoid laying it on where there’s a weld or a screw or a fiting gap, to prevent creating air pockets it may cause it to peel.
4. Position yourself directly in front or behind the piece. Slowly remove the adhesive backing while applying light downward pressure to the pad and constantly evaluating the alignment.
5. Continue this process until the backing is fully removed and the pad is in place.
6. To achieve maximum adhesion, use a roller to apply pressure to the outside of the materials and then roll the entire piece of material inward.
7. Repeat above steps for remaining pads, Wait 24 hours for the glue to stick down before using.

• When not in use, cover the EVA foam flooring to lessen its exposure to direct sunlight to extend its lifespan.
• If there’s fish blood or spill on the EVA foam boat flooring, it’s recommended to wash and clean it asap. Once the stain is dry, it is not easy to wash off.
• Not recommend to put it underneath the fuel tanks at the back, because petrol will destroy the EVA foam, it may turns brittle and peel up.
• lf peeling occur, please clean the surface well, and re-adhere the deck with additional glue, such as 3M spray adhesive, polyurethane glue.

We offer complete customer satisfaction of replacement or refund for any quality issues to the original purchaser for a period of one(1) Year from the date of purchase, if you have any problem with our product, please provide your order number and product damage pictures. You can reach us on Contact Seller page or Email and we will help you further. This is After-Sales info, order of the EVA foam boat decking please go to Platform link to place an order.